Toyota Tacoma (2015-2018) Service Manual: Ambient Temperature Sensor

Toyota Tacoma (2015-2018) Service Manual / Air Conditioning / Ambient Temperature Sensor

Components

COMPONENTS

ILLUSTRATION

Inspection

INSPECTION

PROCEDURE

1. INSPECT AMBIENT TEMPERATURE SENSOR

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection	Condition	Specified Condition
1 - 2	10°C (50°F)	3.00 to 3.73 kΩ
1 - 2	15°C (59°F)	2.45 to 2.88 kΩ
1 - 2	20°C (68°F)	1.95 to 2.30 kΩ
1 - 2	25°C (77°F)	1.60 to 1.80 kΩ
1 - 2	30°C (86°F)	1.28 to 1.47 kΩ
1 - 2	35°C (95°F)	1.00 to 1.22 kΩ
1 - 2	40°C (104°F)	0.80 to 1.00 kΩ
1 - 2	45°C (113°F)	0.65 to 0.85 kΩ
1 - 2	50°C (122°F)	0.50 to 0.70 kΩ
1 - 2	55°C (131°F)	0.44 to 0.60 kΩ
1 - 2	60°C (140°F)	0.36 to 0.50 kΩ

NOTICE:

Even slightly touching the sensor may change the resistance value. Be sure to hold the sensor connector.
When measuring, the sensor temperature must be the same as the ambient temperature.

HINT:

As the temperature increases, the resistance decreases (see the graph).

If the resistance is not as specified, replace the ambient temperature sensor.

Removal

REMOVAL

PROCEDURE

1. REMOVE RADIATOR GRILLE

2. REMOVE AMBIENT TEMPERATURE SENSOR

(a) Disengage the harness clamp.

(b) Disconnect the connector and remove the ambient temperature sensor.

Installation

INSTALLATION

PROCEDURE

1. INSTALL AMBIENT TEMPERATURE SENSOR

(a) Engage the harness clamp and install the ambient temperature sensor.

(b) Connect the connector.

2. INSTALL RADIATOR GRILLE

Blower Motor Controller

Air Outlet Control Servo Motor

Inspection INSPECTION PROCEDURE 1. INSPECT MODE CONTROL SERVO MOTOR (a) Inspect the servo motor operation. (1) When 12V is applied between terminals 4 (IGN) and 1 (GND), and 0V ...

Blower Motor Controller

Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (See page ) 2. REMOVE INSTRUMENT LOWER PANEL ASSEMBLY 3. REMOVE ...

Other materials:

Steering Angle Sensor Power Source Voltage Malfunction (C1432)
DESCRIPTION Steering angle sensor (spiral cable with sensor sub-assembly) signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point m ...

Driving assist systems
To help enhance driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake Syst ...

Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: Be sure to perform this procedure with several people as the transfer assembly is very heavy. PROCEDURE 1. INSTALL TRANSFER CASE LOWER PROTECTOR (a) Install the transfer case lower protector with the 4 bolts. Torque: 18 N·m {184 kgf·cm, 13 f ...