Toyota Tacoma (2015-2018) Service Manual: Air Mix Damper Position Sensor Circuit (Driver Side) (B1436/36)

Toyota Tacoma (2015-2018) Service Manual / Air Conditioning / Air Conditioning System(for Automatic Air Conditioning System) / Air Mix Damper Position Sensor Circuit (Driver Side) (B1436/36)

DESCRIPTION

This sensor detects the position of the air mix damper (for driver side) and sends the appropriate signals to the air conditioning amplifier assembly. The position sensor is built into the No. 3 air conditioning radiator damper servo sub-assembly (for driver side air mix).

DTC No.	DTC Detection Condition	Trouble Area
B1436/36	Short to ground or power source circuit air mix damper position sensor (for driver side) circuit.	No. 3 air conditioning radiator damper servo sub-assembly (for driver side air mix) Harness or connector Air conditioning amplifier assembly

WIRING DIAGRAM

PROCEDURE

1.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Operate the driver side temperature switch.

(e) Enter the following menus: Body Electrical / Air Conditioner / Data List.

(f) Check the value(s) by referring to the table below.

Air Conditioner

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Air Mix Damper Position (Driver Side)	Air mix damper servo motor (for driver side) actual position / Min.: -14.0% Max.: 113.5%	MAX COOL: 0.0% MAX HOT: 100.0%	-
Air Mix Damper Target (Driver Side)	Air mix damper servo motor (for driver side) target position / Min.: -14.0% Max.: 113.5%	MAX COOL: 0.0% MAX HOT: 100.0%	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Air Mix Damper Position (Driver Side)

Air mix damper servo motor (for driver side) actual position /

Min.: -14.0%

Max.: 113.5%

MAX COOL: 0.0%

MAX HOT: 100.0%

Air Mix Damper Target (Driver Side)

Air mix damper servo motor (for driver side) target position /

Min.: -14.0%

Max.: 113.5%

MAX COOL: 0.0%

MAX HOT: 100.0%

OK:

The display is as specified in the Normal Condition column.

Result	Proceed to
NG	A
OK (When troubleshooting according to Problem Symptoms Table)	B
OK (When troubleshooting according to the DTC)	C

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.	INSPECT NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (FOR DRIVER SIDE AIR MIX)

(a) Remove the No. 3 air conditioning radiator damper servo sub-assembly (for driver side air mix) (See page (b) Inspect the No. 3 air conditioning radiator damper servo sub-assembly (for ).

(b) Inspect the No. 3 air conditioning radiator damper servo sub-assembly (for driver side air mix) (See page ).

REPLACE NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (FOR DRIVER SIDE AIR MIX)

3.	CHECK HARNESS AND CONNECTOR (NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

(a) Disconnect the D30 No. 3 air conditioning radiator damper servo sub-assembly (for driver side air mix) connector.

(b) Disconnect the A35 and A36 air conditioning amplifier assembly connectors.

Standard Resistance:

Tester Connection	Condition	Specified Condition
D30-1 (SG) - A35-17 (SG-4)	Always	Below 1 Ω
D30-2 (TPD) - A35-5 (TPL)	Always	Below 1 Ω
D30-3 (S5) - A36-14 (S5-3)	Always	Below 1 Ω
D30-1 (SG) or A35-17 (SG-4) - Body ground	Always	10 kΩ or higher
D30-2 (TPD) or A35-5 (TPL) - Body ground	Always	10 kΩ or higher
D30-3 (S5) or A36-14 (S5-3) - Body ground	Always	10 kΩ or higher

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR

Air Outlet Damper Position Sensor Circuit (B1433/33)

DESCRIPTION This sensor detects the position of the mode damper and sends the appropriate signals to the air conditioning amplifier assembly. The position sensor is built into the No. 1 air condi ...

Air Inlet Damper Control Servo Motor Circuit (B1442/42)

DESCRIPTION This No. 1 air conditioning servo assembly (fresh/recirculation damper) is controlled by the air conditioning amplifier assembly and moves the air inlet damper to the desired position ...

Other materials:

Hydraulic Test
HYDRAULIC TEST 1. PERFORM HYDRAULIC TEST (a) Measure the line pressure. CAUTION: The line pressure test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test. NOTICE: Perform ...

Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch to the LOCK position. The fuses are located in the following places. To check the fuses, follow the instructions below. Engine comp ...

Skid Control Buzzer Circuit (C1AA7)
DESCRIPTION The forward recognition camera operates the pre-collision warning by sending a buzzer request signal to the skid control buzzer. If the forward recognition camera detects a malfunction in the skid control buzzer circuit, it will output DTC C1AA7. DTC No. Dete ...