Toyota Tacoma (2015-2018) Service Manual: Air Inlet Damper Position Sensor Circuit (B1432/32)

Toyota Tacoma (2015-2018) Service Manual / Air Conditioning / Air Conditioning System(for Automatic Air Conditioning System) / Air Inlet Damper Position Sensor Circuit (B1432/32)

DESCRIPTION

This sensor detects the position of the air inlet damper and sends the appropriate signals to the air conditioning amplifier assembly. The position sensor is built into the No. 1 air conditioning servo assembly (fresh/recirculation damper).

DTC No.	DTC Detection Condition	Trouble Area
B1432/32	Short to ground or power source circuit air inlet damper position sensor circuit.	No. 1 air conditioning servo assembly (fresh/recirculation damper) Harness or connector Air conditioning amplifier assembly

WIRING DIAGRAM

PROCEDURE

1.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Operate the recirculation/fresh switch.

(e) Enter the following menus: Body Electrical / Air Conditioner / Data List.

(f) Check the value(s) by referring to the table below.

Air Conditioner

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Air Inlet Damper Position	Air inlet damper servo motor actual position / Air inlet damper servo motor actual position / Min.: -14.0% Max.: 113.5%	FRESH: 0.0% RECIRCULATION: 100.0%	-
Air Inlet Damper Target	Air inlet damper servo motor target position / Min.: -14.0% Max.: 113.5%	FRESH: 0.0% RECIRCULATION: 100.0%	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Air Inlet Damper Position

Air inlet damper servo motor actual position /

Air inlet damper servo motor actual position / Min.: -14.0%

Max.: 113.5%

FRESH: 0.0%

RECIRCULATION: 100.0%

Air Inlet Damper Target

Air inlet damper servo motor target position /

Min.: -14.0%

Max.: 113.5%

FRESH: 0.0%

RECIRCULATION: 100.0%

OK:

The display is as specified in the Normal Condition column.

Result	Proceed to
NG	A
OK (When troubleshooting according to Problem Symptoms Table)	B
OK (When troubleshooting according to the DTC)	C

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.	INSPECT NO. 1 AIR CONDITIONING SERVO ASSEMBLY (FRESH/RECIRCULATION DAMPER)

(a) Remove the No. 1 air conditioning servo assembly (fresh/recirculation damper) (See page (b) Inspect the No. 1 air conditioning servo assembly (fresh/recirculation damper) ).

(b) Inspect the No. 1 air conditioning servo assembly (fresh/recirculation damper) (See page ).

REPLACE NO. 1 AIR CONDITIONING SERVO ASSEMBLY (FRESH/RECIRCULATION DAMPER)

3.	CHECK HARNESS AND CONNECTOR (NO. 1 AIR CONDITIONING SERVO ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

(a) Disconnect the D29 No. 1 air conditioning servo assembly (fresh/recirculation damper) connector.

(b) Disconnect the A35 and A36 air conditioning amplifier assembly connectors.

Standard Resistance:

Tester Connection	Condition	Specified Condition
D29-1 (SG) - A36-13 (S5-2)	Always	Below 1 Ω
D29-2 (TPI) - A35-6 (TPI)	Always	Below 1 Ω
D29-3 (S5) - A35-16 (SG-3)	Always	Below 1 Ω
D29-1 (SG) or A36-13 (S5-2) - Body ground	Always	10 kΩ or higher
D29-2 (TPI) or A35-6 (TPI) - Body ground	Always	10 kΩ or higher
D29-3 (S5) or A35-16 (SG-3) - Body ground	Always	10 kΩ or higher

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR

Air Mix Damper Position Sensor Circuit (Passenger Side) (B1431/31)

DESCRIPTION This sensor detects the position of the air mix damper (for front passenger side) and sends the appropriate signals to the air conditioning amplifier assembly. The position sensor is ...

Lost Communication with ECM (U0100,U0142,U0155)

DESCRIPTION DTC No. DTC Detecting Condition Trouble Area U0100 No communication with ECM CAN communication system ...

Other materials:

Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (P0776)
SYSTEM DESCRIPTION The ECM uses the vehicle speed signal and signals from the transmission revolution sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of t ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals ...

Removal
REMOVAL CAUTION / NOTICE / HINT NOTICE: If one of the camshaft timing gear bolts is already removed, do not remove any other camshaft timing gear bolts. PROCEDURE 1. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package) 2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY 3. REMOVE ...