Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: A-TRAC Indicator Light Remains ON

DESCRIPTION

This is the A-TRAC main switch circuit. When the A-TRAC switch is turned on with the transfer in L4, the A-TRAC function is available and the A-TRAC indicator light illuminates.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page ). Inspect the fuses for circuits related to this system before performing ).
  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (See page OK: OK: ).

OK:

CAN Bus Check indicates no malfunctions in CAN communication.

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

OK

2.

CHECK HARNESS AND CONNECTOR (ATRC TERMINAL)

(a) Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

S1-13 (TRM3) - Body ground

A-TRAC switch not pushed in

10 kΩ or higher

A-TRAC switch pushed in

Below 1 Ω

Text in Illustration

*a

Front view of wire harness connector

(to Skid Control ECU (Master Cylinder Solenoid))

(c) Reconnect the S1 skid control ECU (master cylinder solenoid) connector.

NG

GO TO STEP 4

OK

3.

READ VALUE USING TECHSTREAM (A-TRC(TRAC) SWITCH)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

ABS/VSC/TRAC

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

A-TRC(TRAC) Switch

A-TRC Switch/ ON or OFF

ON: A-TRC switch on

OFF: A-TRC switch off

-

(f) Check that the mode display changes according to A-TRAC OFF switch operation.

OK:

Display changes according to switch operation.

A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

REPLACE MASTER CYLINDER SOLENOID

4.

INSPECT A-TRAC SWITCH

(a) Remove the A-TRAC switch (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

5 - 8

Switch is not pushed

Below 1 Ω

Switch is pushed

10 kΩ or higher

Text in Illustration

*a

Component without harness connected

(A-TRAC Switch)

NG

REPLACE A-TRAC SWITCH

OK

5.

INSPECT ROOF CONSOLE BOX ASSEMBLY

(a) Remove the roof console box assembly.

  • for Double Cab: (See page ) for Access Cab: (See page )
  • for Access Cab: (See page ) )
Text in Illustration

*a

Component without harness connected

(Roof Console Box Assembly)

-

-

(b) Measure the resistance according the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R44-7 (ATRC) - 8

Always

Below 1 Ω

R44-12 (GND) - 5

Always

Below 1 Ω

Result

Result

Proceed to

OK

A

NG (for Double Cab)

B

NG (for Access Cab)

C

A

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASTER CYLINDER SOLENOID - ROOF CONSOLE BOX ASSEMBLY)

B

REPLACE ROOF CONSOLE BOX ASSEMBLY

C

REPLACE ROOF CONSOLE BOX ASSEMBLY

A-TRAC Indicator Light does not Come ON
DESCRIPTION The A-TRAC does not operate even if the A-TRAC switch is pressed under the following conditions: The TRAC or VSC system is faulty. The temperature inside the hydraulic brake ...

VSC Buzzer Circuit
DESCRIPTION The skid control ECU (master cylinder solenoid) is connected to the combination meter via CAN communication. The combination meter has a built-in VSC warning buzzer: Sounds int ...

Other materials:

Removal
REMOVAL CAUTION / NOTICE / HINT NOTICE: When replacing the forward recognition camera, replace it with a new one. Do not touch the camera lens or the front windshield glass in front of the camera. If the forward recognition camera has been struck or dropped, replace it ...

Front Speed Sensor RH Output Malfunction (C1413,C1414)
DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC No. Detection Item DTC Detection Condition Trouble Area C1413 Front Speed Sensor RH Output Malfunction Any of the following is detected: An o ...

Portable Player cannot be Connected Manually/Automatically
CAUTION / NOTICE / HINT HINT: Some versions of "Bluetooth" compatible audio players may not function, or the function may be limited using the radio and display receiver assembly, even if the portable audio player itself can play files (See page ). PROCEDURE 1. ...

© 2011-2024 Copyright www.ttguide.net