Toyota Tacoma (2015-2018) Service Manual: 4WD ECU Malfunction (P163B)

Toyota Tacoma (2015-2018) Service Manual / Differential / Differential System(w/ Rear Differential Lock) / 4WD ECU Malfunction (P163B)

DESCRIPTION

This DTC is output when a malfunction is detected in the 4 wheel drive control ECU internal circuit.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
P163B	4WD ECU Malfunction	Diagnosis Condition: Directly after ignition switch is turned to ON, or when switching operations are performed with ignition switch turned to ON Malfunction Status: 4 wheel drive control ECU internal circuit malfunction Malfunction Time: 0.5 seconds or more (directly after the ignition switch is turned to ON, 0.05 seconds or more) Other: 1 trip detection logic	Wire harness and connector Differential lock coil 4 wheel drive control ECU

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

4WD specification:

If P163B is detected, troubleshoot the TOUCH SELECT 2-4 AND HIGH-LOW system first.

PROCEDURE

1.	CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL LOCK COIL)

(a) Turn the ignition switch off.

(b) Disconnect the F12 4 wheel drive control ECU connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
F12-1 (SL+) - D28-2 (SL+)	Always	Below 1 Ω
F12-5 (SL-) - D28-1 (SL-)	Always	Below 1 Ω
F12-1 (SL+) or D28-2 (SL+) - Body ground	Always	10 kΩ or higher
F12-5 (SL-) or D28-1 (SL-) - Body ground	Always	10 kΩ or higher

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
F12-1 (SL+) or D28-2 (SL+) - Body ground	Ignition switch ON	Below 1 V
F12-5 (SL-) or D28-1 (SL-) - Body ground	Ignition switch ON	Below 1 V

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.	INSPECT DIFFERENTIAL LOCK COIL

(a) Turn the ignition switch off.

(b) Disconnect the D28 differential lock coil connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 (SL-) - 2 (SL+)	Always	2.65 to 2.95 Ω
1 (SL-) or 2 (SL+) - Body ground	Always	10 kΩ or higher

Text in Illustration

*a	Component without harness connected (Differential Lock Coil)

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
1 (SL-) or 2 (SL+) - Body ground	Ignition switch ON	Below 1 V

REPLACE 4 WHEEL DRIVE CONTROL ECU

REPLACE DIFFERENTIAL LOCK COIL

Rear Differential Lock Position SW Stuck ON (P17BC)

DESCRIPTION This DTC is output when an ON malfunction of the differential lock indicator switch is detected. DTC No. Detection Item DTC Detection Condition ...

ECU Power Source Circuit

WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspection procedure. PROCEDURE 1. ...

Other materials:

Installation
INSTALLATION PROCEDURE 1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (a) Install the transmission control cable assembly from outside the vehicle body and attach the 3 claws of the cable retainer. (b) Install the 2 nuts. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} (c) Connect the transmissi ...

Dtc Check / Clear
DTC CHECK / CLEAR NOTICE: When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type u ...

Door Control Receiver
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE ROOF HEADLINING ASSEMBLY (for Double Cab) (See page ) 2. REMOVE ROOF HEADLINING ASSEMBLY (for Access Cab) (See page ) 3. REMOVE DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System) (a) Disconne ...