DESCRIPTION
The forward recognition camera receives vehicle speed tolerance signals from the combination meter assembly. If the combination meter assembly detects a vehicle speed tolerance malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA2 is stored.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AA2 |
Vehicle Speed Tolerance Malfunction |
When the vehicle is being driven at a speed of 5 km/h (3 mph) or more 3 seconds after the ignition switch is turned to ON, a signal from the combination meter assembly indicating an abnormal vehicle speed tolerance is detected by the forward recognition camera for 50 seconds or more. |
|
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
- If the forward recognition camera has been replaced with a new one,
be sure to perform forward recognition camera learning.
Click here
.gif)
- First check the CAN communication system by following How to Proceed
with Troubleshooting. After checking that there are no malfunctions in the
CAN communication system, proceed with troubleshooting.
Click here
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
|
1. |
CHECK FOR DTCs (METER / GAUGE SYSTEM) |
HINT:
Lane departure alert system DTC C1AA2 may be stored due to a malfunction in the meter/gauge system. Therefore it is necessary to check for and troubleshoot meter/gauge system DTCs first.
(a) Check for DTCs.
Body Electrical > Combination Meter > Trouble Codes|
Result |
Proceed to |
|---|---|
|
Meter/gauge system DTCs are not output |
A |
|
Meter/gauge system DTCs are output |
B |
| B | .gif) |
CHECK METER / GAUGE SYSTEM |
|
.gif)
|
2. |
CHECK DTC OUTPUT |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
(e) Clear the DTCs.
Click here
(f) Make sure that the DTC detection conditions are met.
HINT:
If the following procedure is not performed, the previously output DTC cannot be detected.
(g) Check for DTCs.
Click here
|
Result |
Proceed to |
|---|---|
|
DTC C1AA2 is output |
A |
|
DTC C1AA2 is not output |
B |
| B | |
USE SIMULATION METHOD TO CHECK |
|
|
3. |
REPLACE FORWARD RECOGNITION CAMERA |
(a) Replace the forward recognition camera.
Click here
(b) Adjust the forward recognition camera.
Click here
|
|
4. |
CHECK DTC OUTPUT |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
(e) Clear the DTCs.
Click here
(f) Make sure that the DTC detection conditions are met.
HINT:
If the following procedure is not performed, the previously output DTC cannot be detected.
(g) Check for DTCs.
Click here
|
Result |
Proceed to |
|---|---|
|
DTC C1AA2 is output |
A |
|
DTC C1AA2 is not output |
B |
| A | |
REPLACE COMBINATION METER ASSEMBLY |
| B | |
END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE) |
