Toyota Tacoma manuals

Opel Insignia B 2018-2022 Owners Manual: Bulb Replacement

For the proper type of replacement bulbs, or any bulb changing procedure not listed in this section, contact your dealer.

Halogen Bulbs

Warning: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.

High Intensity Discharge (HID) Lighting

Warning: The High Intensity Discharge (HID) lighting system operates at a very high voltage. If you try to service any of the system components, you could be seriously injured. Have your dealer or a qualified technician service them.

After an HID headlamp bulb has been replaced, the beam might be a slightly different shade than it was originally. This is normal.

Headlamps

Driver Side Shown, Passenger Driver Side Shown, Passenger Side Similar

  1. Low Beam
  2. High Beam

Low-Beam Headlamp/Daytime Running Lamp (Base)

1. For the driver side bulb, remove the windshield washer bottle filler neck by firmly pulling it straight up and out of the bottle.

2. Remove the cap from the back of the headlamp assembly.

3. Disconnect the electrical connector.

4. Remove the bulb socket from the headlamp assembly.

5. Reverse Steps 1-4 to install.

High/Low-Beam Headlamps (Uplevel)

The high/low-beam headlamps on the uplevel headlamp system are Light Emitting Diode (LED) and should be replaced by your dealer.

Fog Lamps

To replace the fog lamp bulb:

To replace the fog lamp bulb:

1. Locate the bulb assembly under the front fascia.

2. Disconnect the electrical connector from the bulb assembly.

3. Remove the bulb by turning it counterclockwise and pulling it straight out of the assembly.

4. Install the new bulb by turning it clockwise into the assembly.

5. Reconnect the electrical connector to the bulb assembly.

Front Turn Signal Lamps

Sidemarkers, daytime running lamps and turn signal lamps are LEDs and cannot be changed.

See your dealer.

Taillamps, Turn Signal, Stoplamps, and Back-Up Lamps

Driver Side Shown, Passenger Driver Side Shown, Passenger Side Similar

To replace any one of these bulbs:

1. Open the liftgate.

2. Remove the rear cargo area

2. Remove the rear cargo area trim panel push pin.

3. Pull the rear cargo area trim panel back to gain access to the taillamp assembly.

4. Remove the two nuts that

4. Remove the two nuts that secure the taillamp assembly.

5. Remove the taillamp assembly and disconnect the wiring harness connector.

6. Turn the bulb socket counterclockwise to remove it.

7. Pull the bulb from the socket.

8. Install a new bulb.

9. Turn the bulb socket clockwise to install it.

10. Reverse Steps 2-4 to reinstall the taillamp assembly.

Vehicle Checks
Doing Your Own Service Work Warning: It can be dangerous to work on your vehicle if you do not have the proper knowledge, service manual, tools, or parts. Always follow owner's manual procedures and c ...

Electrical System
Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and c ...

Other materials:

Inspection
INSPECTION PROCEDURE 1. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Text in Illustration *a Component without harness connected (Headlight Dimme ...

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (See page ) 2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG (See page ) 3. ...

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT BRAKE PEDAL HEIGHT (a) Check the brake pedal height. Pedal height from dash panel: Type Pedal Height Automatic transmission 164.4 to 174.4 mm (6.473 to 6.866 in.) Manual transmission ...

В© 2011-2022 Copyright www.ttguide.net