PROCEDURE
1. |
CHECK USAGE CONDITION |
(a) Check that the vehicle and cellular phone meet the following conditions:
NOTICE:
If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.
(b) Register the cellular phone again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A | ![]() |
END |
|
2. |
RESTART CELLULAR PHONE |
(a) Restart the cellular phone.
(b) Turn the ignition switch off.
(c) Turn the ignition switch to ACC.
(d) Register the cellular phone as a connected device again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A | ![]() |
END |
|
3. |
BRING CELLULAR PHONE NEAR IN-VEHICLE DEVICE |
(a) Place the cellular phone close to the radio and display receiver assembly.
(b) Register the cellular phone as a connected device again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A | ![]() |
END |
|
4. |
CLEAR REGISTERED DEVICE INFORMATION |
(a) Clear all "Bluetooth" devices registered to the radio and display receiver assembly and delete the radio and display receiver assembly information from the cellular phone.
(b) Register the cellular phone as a connected device again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A | ![]() |
USE A "Bluetooth" COMPATIBLE CELLULAR PHONE |
|
5. |
CHECK USING ANOTHER VEHICLE |
(a) Check if the cellular phone can be registered normally to another "Bluetooth" compatible vehicle of the same model.
HINT:
Result |
Proceed to |
---|---|
Cellular phone can be registered. |
A |
Cellular phone cannot be registered. |
B |
A | ![]() |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
|
6. |
CHECK USING ANOTHER CELLULAR PHONE |
(a) Using another "Bluetooth" compatible cellular phone, register the cellular phone and check that it is registered correctly.
HINT:
Result |
Proceed to |
---|---|
Cellular phone can be registered. |
A |
Cellular phone cannot be registered. |
B |
A | ![]() |
END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED) |
B | ![]() |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
Blower Motor Circuit
DESCRIPTION
The blower motor with fan sub-assembly operates according to signals from the
air conditioning amplifier assembly. The blower motor with fan sub-assembly speed
signals are transmitted by changes in the duty ratio.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuse ...
GPS Mark is not Displayed
PROCEDURE
1.
CHECK CABIN
(a) Check the cabin for any object that might interrupt radio reception or additional
devices which use radio waves on the instrument panel. If such an object exists,
remove it and check if the GPS mark reappears.
HINT:
The GPS uses ex ...
Replacement
REPLACEMENT
PROCEDURE
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
(a) Start up the engine.
(b) Turn the A/C switch to ON.
(c) Operate the cooler compressor with an engine speed of approximately 1,000
rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil
rem ...